BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ Manual transmission and transmission a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   + Forward suspension bracket
   + Back suspension bracket
   - Steering with the hydraulic booster (сервоуправление)
      Removal and installation of the block of a pillow of safety on a steering wheel
      Removal and steering wheel installation
      Removal and installation of a tip of steering draught
      Removal and installation of steering draught
      Removal and installation of the pump of the hydraulic booster
      Filling with a liquid and removal of air from hydrosystem of the amplifier of a wheel
      Corners of installation of forward wheels. Check of installation of wheels
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation of a tip of steering draught

The steering mechanism, covers and steering draughts

1 — steering draught right
2 — vрулевая draught left
3 — nut М12, 65 Н•м
Self-stopped, necessarily replace
4 — the complete set of covers of the steering mechanism right
5 — the steering mechanism
6 — the complete set of covers of the steering mechanism left
7 — a tip of steering draught
8 — a ring tightening

9 — a nut tightening, 80 Н•м
10 — a collar, 50 – 53 mm
11 — a ring basic
It is inserted into narrowing of steering draught near to шестигранной a nut. Before installation of steering draught grease it консистентной with greasing at narrowing that at draught turn to exclude joint rotation of a cover.
12 — a cover
13 — a collar, 65 – 68 mm


 REMOVAL

1 Mark a paint position of a forward wheel concerning a nave. It will allow to establish отбалансированное a wheel in the former position. Loosen the bolts of fastening of a wheel at the car standing on the earth. Lift a forward part of the car and remove a wheel.

2 Measure the size - And - between the hinge and the end of a carving of steering draught
-5 also write down the received value.

3 Oslabte a tightening nut-1 tips of steering draught-2, address to Section Corners of installation of forward wheels. Check of installation of wheels.

4 Turn away a nut of fastening-3 hinges of steering draught-4. 2 – a tip of steering draught.

5 Remove a tip of steering draught by means of tool HAZET779–1.

6 Turn away a tip from steering draught, keeping thus draught a wrench for шестигранник-5 from проворачивания.

At отворачивании count number of turns and write down the received value. It will facilitate the further adjustment of forward wheels.


 INSTALLATION

7 Establish on steering draught a tightening ring if it acted in film.
8 Screw a tip of steering draught, the number of turns should be equal to number of turns at removal. Check up the size - And - received before removal.
9 If it is necessary, clear of greasing a pin of the hinge of steering draught, and also an aperture in a rotary fist.
10 Insert a tip of steering draught, and also an aperture into a rotary fist. Screw a new self-stopped nut on a pin of the hinge and tighten its moment 65 Н•м.
11 Tighten a tightening nut of a tip of steering draught the moment 80 Н•м. Thus keep draught from проворачивания for шестигранник.
12 Establish into place a wheel so that the marks put at removal, have coincided. Preliminary grease with a thin layer подшипниковой greasings a seat of a disk of a wheel on a nave. Bolts of fastening of a wheel do not grease. Rusty bolts replace with the new. Fix a wheel bolts. Lower the car on wheels and tighten bolts cross-wise the moment 100 Н•м.
13 Check up a track on HUNDRED, if necessary adjust.