BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ Manual transmission and transmission a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and security measures
   + Leaving and repair of damages of a body
   - External elements of a body
      Removal and installation of a forward bumper
      Removal and installation/check of shock-absorbers of a bumper
      Removal and installation of a back bumper
      Removal and installation of the back shock-absorber
      Removal and cover installation обтекателя
      Removal and installation of a forward wing
      Removal and cowl installation
      Cowl adjustment
      Removal and installation of a cover of a luggage carrier
      Adjustment of a cover of a luggage carrier
      Removal and installation of the lock/cylinder of the lock of a cover of a luggage carrier
      Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
      Replacement молдингов and model emblems
      Removal, installation and door adjustment
      Removal and installation of facing of a door
      Removal and installation of the lock of a door
      Removal and installation of the cylinder of the lock
      Removal and installation of the external handle of a door
      Removal, installation and window adjustment
      Removal and installation electric window lifterа
      Removal and electric motor installation window lifterа
      Removal and installation of a mirror of an external kind / a sound signal of a high-pitch tone
      Removal and installation of glass of a mirror
      Removal and installation of the case of a mirror of an exterior
   + Internal elements of a body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation of facing of a door

Here removal of facing of a forward door is described. Process of removal of facing of a back door is similar. Differences are described in the end of Section.

 REMOVAL

1 Disconnect a negative cable (-) the storage battery at the switched off ignition. The battery is in a luggage compartment behind a cover on the right side. At cars BMW 316i, 318i the battery settles down in an impellent compartment.

As a result of switching-off of the storage battery the data from memory of malfunctions of some monitors is erased. If necessary before battery switching-off it is necessary to consider the given memories of malfunctions. Address to Section Diagnostics of malfunctions. Work it is desirable to spend HUNDRED in conditions.

2 Isolate a negative pole on storage batteries to exclude casual contact to it.

3 Remove upward by means of two small screw-drivers the switch of a mirror-1. Thus screw-drivers are put in the points shown on an illustration by arrows. Расстыкуйте two штекерных connections also remove the mirror switch.

4 Remove fingers a peak-1 from a door from the back face party. Thus start to remove from a back end face. The peak is fixed by four clips.

5 Turn out screws (1/2/3) screw-driver Torx Т20.

The screw-1 is longer than others. Arrows - support for the top peak.

6 Wring out facing from a door and disconnect in points-1. For отжатия use a plastic wedge, for example, HAZET 1965-20.

7 Delay facing above from a door and disconnect in points-2 of скоб, since the party of loops.
8 Lift door facing through the lock button.

9 Disconnect a cable of an internal drive of a door. For this purpose open the lever of an internal drive of a door. In this position disconnect a white plastic clip-1 and remove a cable-2 back with drive the lever.

10 From a facing underside расстыкуйте a loudspeaker socket. Disconnect two fastenings of a cable and stretch electric wires.
11 Remove door facing.

12 Check up clips of facing of a door, if necessary replace.

Before removal of a pillow of safety necessarily familiarise with safety rules concerning a pillow, address to Section the Steering with the hydraulic booster (сервоуправление).


13 Turn away three bolts of fastening-3 lateral pillows of safety-1. From an underside расстыкуйте a socket of yellow colour also remove a safety pillow.

Fastening bolts are covered by means for fixing of carving connections and it is necessary to replace them.

14 Disconnect on a contour a cover-1 from a door. For this purpose pull it a few fingers, then a plastic wedge wring out the glutinous platen on a door.

Especially cautiously operate in the bottom and forward part - And-. It is necessary to replace the damaged cover of a door.


 INSTALLATION

15 Carefully paste a cover on door cut. Thus watch that it has coincided with apertures.

Watch to damaging a door cover, otherwise in the car there will be a draught. The glutinous weight should be put on a contour. If necessary it is necessary to restore glutinous consolidation with the help бутилового cord BMW.

16 Check up, whether the negative cable (-) the storage battery is disconnected. If is not present, disconnect it at the switched off ignition.
17 Establish into place a lateral pillow of safety. For this purpose join a socket of yellow colour from an underside and fix it so that distinct click was audible. Check up reliability of fixing штекерного connections. Fix a lateral pillow of safety three new screws the moment 8.5 Н•м.

18 Check up reliability of fastening of clips-1 facings of a door, if necessary replace. 2 – support top скоб.

19 Stretch from a facing underside electric wires. Fix cables and join a loudspeaker socket. If necessary fix the tip of a drive of a mirror a sticky tape in cut of facing of a door.
20 Connect a cable of an internal drive of a door in the lever. Thus a clip insert in front, press behind and fix a hook.
21 Raise door facing over the fixing button.
22 Establish facing from above at скоб and press. If necessary slam a palm.
23 Expose facing over apertures of plastic clips and cautiously slam palms.

24 Fix screws (1/2/3) facing of a door. Thus watch that longer screw has been screwed in a point-1.

25 Insert the top peak with four clips into basic elements and press. If necessary cautiously slam palms.
26 Join a socket of the switch of a mirror and press the switch into an aperture of facing of a door.

During joining of the storage battery in the car there should not be people

27 Attach a negative cable (-) the storage battery at the switched off ignition. Establish hours.

Differences for facing of a back door

Cars with electric window lifterом:


28 Remove upwards the switch window lifterа at the switch.

Cars without electric window lifterа:


29 Remove a peak instead of the switch window lifterа by means of two small screw-drivers.

30 Remove the handle window lifterа. For this purpose:

- Remove a screw-driver a peak (the marksman on an illustration).
- Turn out the screw being under it.
- Remove the handle window lifterа from an axis together with a washer.