BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ Manual transmission and transmission a line
+ Automatic transmission
+ Coupling and power shafts
- Brake system
   Removal and installation brake колодок forward wheels
   Removal and installation directing forward brakes
   Removal and installation of a brake disk of a forward wheel
   Removal and installation brake колодок disk brakes
   Removal and installation скобы brakes of back wheels
   Removal and installation of a brake disk of a back wheel
   Measurement of a thickness of a brake disk
   Brake liquid - the basic data and security measures
   Removal of air from brake system
   Replacement of the brake pipeline
   Replacement of a forward brake hose
   Check of the amplifier of a brake
   Removal and installation колодок a lay brake
   Adjustment of a lay brake
   Removal and installation of the lever of a lay brake
   Removal and installation of a cable of a drive of a lay brake
   Removal and installation of the switch of a stoplight
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes



Removal and installation колодок a lay brake

The lever of a lay brake

1 — the lever of a lay brake
2 — a cover
3 — a counternut
4 — an adjusting nut

5 — a bolt
6 — the switch of a lay brake
7 — a cable of a drive of a lay brake


Колодки a lay brake

1 — a drive cable
2 — a bolt
3 — a support
4 — brake колодка
5 — the lock
6 — a finger

7 — the adjusting screw
8 — the bottom coupling spring
9 — the top coupling spring
10 — a compression spring
11 — a pin


 REMOVAL

1 Remove a back brake disk.

2 Disconnect by means of nippers a forward returnable spring, a spring with traces of corrosion or the weakened spring replace.

3 compress a spring a face key on 5 mm a little, turn on a corner 90 (1/4 turns) and remove a press spring with brake Pads.

4 Similarly remove a spring from another brake Pads.

5 Separate both brake Pads above and remove downwards.

6 Check up ease of a course of the lock, if necessary remove it. For this purpose pull an element-1 back, squeeze out a finger-2 and remove an element-3 from a cable.


 INSTALLATION

Necessarily replace brake Pads on both parties.
1 Slightly grease sliding surfaces and a finger of the lock with greasing “Molykote-Paste-G”.

2 Connect above the lock to a finger-2 with a cable of a drive of a brake.

3 Check up movement of the mechanism of adjustment brake колодок-1, slightly grease a carving with greasing “Molykote”. Turn on back a carving element.

4 Establish the mechanism of adjustment brake колодок below between brake колодками. Connect a returnable spring-2 (a spring of smaller diameter) with brake колодками. 3 – the top returnable spring.

5 Insert into place brake Pads. Above brake Pads should enter into grooves (arrows on an illustration) the lock.

6 Press two springs of compression by a face key on 5 mm and simultaneously turn on a corner 90 . In the closed position marks on a screw head cost, as is shown in an illustration.

7 By means of nippers for a brake spring connect the top returnable spring.

8 Brake Pads (arrows on an illustration) should adjoin to a support скобы brakes.

9 Establish to the place of a brake disk and a back wheel.
10 Adjust a lay brake, address to Section Adjustment of a lay brake.

If brake Pads a lay brake were replaced, them it is necessary to earn extra on road with неинтенсивным transport as follows. Moving with a speed of 40 km/hour, cautiously tighten a lay brake so that easy braking was felt. At preservation of speed of movement tighten a brake on one tooth and pass so about 400 m. Release a brake and allow to it to be cooled. It is recommended to repeat this process once in three months irrespective of brake replacement so the rust which can be formed on a frictional surface, and deterioration products thus leaves.